CAD design

Thermal expansion in design: why plastics and metal need clearance

Plastic expands several times more than aluminium or steel. Characteristic values, a worked example, and design rules for clearance, slotted holes and supports.

Date
Reading time
6 min
Author
Konstantin Vinogradov
CAD render of the KANID SoloMeter 2.0 with a tripod and a seat for the surveyor’s folding rule (provisional header image; a motif on thermal expansion will follow)

A plastic lid sits in an aluminium frame, flush and with no gap. In the workshop everything fits. A few months later the feedback arrives: in summer the lid jams, in winter it rattles. The fault is not in the material and not in the manufacture, but in a number that was missing from the design: the coefficient of thermal expansion.

What thermal expansion means

Almost every material becomes longer when heated and shorter when cooled. How much is described by the linear coefficient of thermal expansion α. It states by what fraction of its length a part expands per kelvin of temperature change. The change in length can be estimated simply:

ΔL = α · L · ΔT

ΔL is the change in length, L the original length and ΔT the temperature difference in kelvin (1 K corresponds to a 1 °C difference).

Characteristic values: plastic versus metal

Typical values from the Engineering ToolBox table, each in 10−6 per kelvin:

Material α (10−6 / K)
Steel 10.8 – 12.5
Copper 16 – 16.7
Brass 18 – 19
Aluminium 23 (alloys 21 – 24)
Polyamide, glass-fibre-reinforced 23
Polycarbonate (PC) 65 – 70
Acrylic (PMMA) 68 – 75
ABS 72 – 108
Polypropylene (PP) 72 – 90
Polyacetal (POM) 85 – 110

Characteristic values: The Engineering ToolBox, Linear Thermal Expansion Coefficients of Materials (retrieved 19 November 2026).

Two things stand out. First: unfilled plastics expand about three to five times as much as aluminium, and still more clearly than steel. Second: fillers change the picture considerably. Glass-fibre-reinforced polyamide is in the same order of magnitude as aluminium. The values vary by grade. For the design, therefore, the data sheet of the actual material counts; the table shows the order of magnitude.

Worked example: 200 millimetres, 40 kelvin

A part is 200 mm long; the temperature difference between the coldest and the warmest state is 40 K:

If an ABS strip sits without clearance in an aluminium frame, when heated it grows by about 0.4 to 0.7 mm more than the frame. That difference has to go somewhere. Either there is clearance, or the plastic part bows, jams or presses on screws and clips. When it cools, the opposite happens: the flush fit becomes a gap.

Design rules for plastic-to-metal joints

1. Set the temperature range before you start designing. Where will the product be stored, transported and used? That question belongs in the requirements specification (Lastenheft). Without it, no sensible clearance can be set.

2. Plan clearance in the direction of the greatest length. Expansion grows with length. On short parts it is often negligible; on long strips, lids and covers it is not. The clearance must take up the difference between the two materials over the full temperature range, plus the manufacturing tolerances.

3. Fix it firmly at only one point. If a long plastic part is bolted rigidly at both ends, it cannot expand. Better: one fixed point, and at the other fixings slotted holes in the direction of expansion, so that the part can slide. The idea is the same as the fixed and floating bearings of a shaft.

4. Do not clamp screws into the plastic where it is meant to slide. A screw with a spacer sleeve or a shoulder holds the part in position without clamping it. That way the slotted hole remains effective.

5. Choose matching materials. If a plastic part has to work closely with metal, a filled plastic with lower expansion can be the better choice. That has consequences for stiffness, surface and cost, and is therefore decided in the concept, not only when ordering.

6. Check it on the prototype. The calculation and the table show the order of magnitude. Whether the fit holds over the temperature range is shown by the prototype. A 3D-printed part can behave differently from the later series part from injection moulding, because the material and the manufacturing process are different. For the series, the data sheet of the series material counts.

Typical mistakes

How I approach this at KANID

Product design and technical development belong together: I think about form, function and manufacture together from the start. For housings and assemblies made of several materials, that means recording the temperature range already in the requirements specification and sizing the fits accordingly. Design is done in Onshape; you review every status via a link in the browser. I print functional prototypes in-house in Filderstadt, so that fit and assembly are tested early. How that relates to manufacture is in the post Design for manufacture in CAD; notes on printed prototypes are in the post Having a 3D-printed prototype made.

The starting point is phase 1, concept & feasibility: requirements specification, solution concept, parts list with sources of supply, a short report on risks, and a binding fixed-price quote for phase 2. Fixed price 1,450 € incl. 19% VAT, duration about 3–4 weeks. Phase 2 through to the pre-series prototype starts from about 5,000 € net; the exact fixed price is set after phase 1. More under Services.

In brief

How much does plastic expand when it gets warm?

Unfilled plastics such as ABS, PP or POM are typically around 70 to 110 · 10−6 per kelvin, roughly three to five times as high as aluminium (23 · 10−6 / K). Exact values are in the data sheet of the material concerned.

How do I calculate linear expansion?

With ΔL = α · L · ΔT. Example: 200 mm of ABS at a 40 K temperature difference gives, depending on the grade, about 0.6 to 0.9 mm.

How much clearance does a plastic part need in a metal frame?

At least the difference in the length changes of both materials over the full temperature range, plus the manufacturing tolerances. The temperature range is set in the requirements specification (Lastenheft).

Does glass fibre help against thermal expansion?

Yes, fillers reduce expansion considerably. Glass-fibre-reinforced polyamide, according to the Engineering ToolBox, is around 23 · 10−6 / K and therefore in the same order of magnitude as aluminium.

thermal expansion of plasticsthermal expansion aluminium and plasticcoefficient of expansion ABScalculate linear expansionclearance between plastic and metal in designCAD design

← Back to the overview

KANID UG
Filderstadt
Sheet
03 / 17
Rev.
Scale
1:1
Title
Blog · CAD design
Drawing no.
KANID-WEB-2026-03
Drawn by
K. Vinogradov
Material / standard
HTML · WCAG 2.1 AA